How much does it cost to install a shower tub combo?

If you wonder how much it will cost to install tub shower combo, it is around $550 to $1100.

How much room do you need for a tub shower combo?

Around 30-inch area is enough for a tub shower combo.

Can you add a tub to an existing shower?

Yes, you can add a tub to an existing shower.

What is the average cost of a Bath Fitter shower?

From $1000 to $10000, but averagely $3000 bucks will cost for a bath fitter shower.

Tool requirements

Caulk gun
Drill bit set
Grout float
Hammer
Cordless drill
Hearing protection
Hole saw kit
4-in-1 screwdriver
Circular saw
Level
Notched trowel
Pipe wrench
Adjustable wrench
Utility knife
Slip joint pliers
Tape measure
Pry bar
Safety glasses

Required materials

Tub/Shower Faucet
1/4-in. backer board (1 sheet)
New Tub and Surround
Plumbing Supplies (as needed)
Backerboard screws (box)
Caulk
1-1/2-in. roofing nails
Adhesive
Two 2x4x8
Grout
Painting supplies
Tile

Install tub shower combo

Some people have tried to install bathtubs without the help of a professional, but they were not successful in their mission. The key reason behind this issue is that they do not follow the correct procedure, which requires precise measurements and knowledge of the plumbing system. If you want to know how to install a bathtub, make sure that you carefully follow these steps.

The first step is to mark the location of where the drain and new tub will be installed. Keeping the spot is very important as you need to make sure that the holes you create will be perfectly straight. Marking the area is also necessary because you need to make sure that you do not miss any place for the drain. The next thing that you need to do is to mark the bathroom subfloor.

Now, you can begin by preparing the subfloor by scraping it using a pneumatic claw hammer. You should remove as much extra material from the walls as possible. You should use caulk to fill all the large holes and spread some of the caulk to the corners. The next thing that you have to do is to remove the old drain. You should follow the manufacturer’s instructions correctly if you decide to hire a plumber for the installation. After the drain is terminated, you should spread some of the caulk to the surrounding areas.

The next step is to install the waste-and-overflow pipe, which is attached to the existing drain line. If you use a plumber for the installation, you should ensure that he follows the instructions strictly. If you are not particular about the procedure, then you can read through the instruction manual carefully. Once you have connected the waste-and-overflow pipes to the drain line, you should reconnect the main water supply to your house.

Once the house has been restored to its original state, you can install the acrylic tub surrounds on the walls. This time, you will have to use plumbing joints rather than glues. For this, you can use a threaded kind of coupling. However, if you are using the new type of fittings, you will have to consult the instructions given by the manufacturer.

When you are installing the plumbing, you should remember that you should always install them in pairs. Otherwise, there is a possibility that they will leak each other when filled with water. You should also install them on both sides of the wall and at an angle. The reason behind this is that you will be cutting the pipes that run below the overflow. If you fail to follow these things, there is a possibility that the pieces of the lines will get disconnected and cause damage to your bathroom walls and floor.

These days, people prefer fiberglass, and acrylic tub surrounds because they are more durable than the older models. They are also resistant to scuff marks, which is the most common problem with the older bathtub models. However, if you Install tub shower combo them incorrectly, you might find them very difficult to remove later. For this reason, it is essential to make sure that you are using the correct fittings when you are installing any bathroom furniture. There is a chance that you will get injured if you ignore the details when you are carrying out the bathtub installation.

The last thing that you need to learn how to install a plastic bathtub is to know how to measure the area where you will install the old tub. It is an essential step, and you should never skip it. If you do not measure the room correctly, then there is a chance that you might find that you have to move the old tub to a much smaller space. If you do not carefully measure the new tub’s size, you might find that you have to pay a lot more money when you finally buy the new one. If you follow the tips mentioned above, you can be sure that you will install your old tub in a much easier and more convenient manner.

Installing an acrylic tub and bath surround can add an instant facelift to the look of your bath area. These are also known as bath-core or bath-surrounds and come in a wide variety of different materials and shapes. There are different styles to choose from, so it may be challenging to find one that fits your existing bath fixtures. This article will provide you with the data you need to select the right tub to surround your home.

The most common acrylic bathtubs and surrounds are made from either fiberglass or acrylic. Fiberglass has a very modern look, while acrylic stands out more with its sleek and smooth look. Because of the material they are constructed from, fiberglass tubs often sink much accessible than acrylic ones.

Acrylic bathtubs have a curved shape, which makes them sit perfectly well with round tub fixtures. These can easily sit flush against any corner of your bathtub, so the overall effect is one of a continuous line that matches the rest of your bath area. You will need a special curtain rod to fit an acrylic surround, and this must be installed behind the tub for proper viewing and safety.

These bathtubs and surrounds are making to accommodate hot water spouts. You will need to measure your hot water supply and determine where the tap will be located on the tub. The mounting strap will fit tightly around the pipe and adjust itself to make sure the distance is stable. The tub and surround can then be fastened securely to the line using the appropriate screws. Some manufacturers allow for screws to be attached with T-clip fasteners, but this is not recommended.

Once the tub and surround have been mounted, the old bathtub surface can be removed and the new acrylic bathtub surface installed. The process involves sliding the new bathtub over the old tub and sealing it at the corners with T-brackets and E-clip fasteners. The old tub must first be drained and then covered in vinyl or acrylic sealer to Install tub shower combo.

If you choose to use a fiberglass tub, you will first need to remove the fiberglass top and bottom before beginning your installation. Then, the surrounding edges and the tub sides need to be sanded down slightly to create a smooth surface for the surround to sit on. To seal the covers, you will need to apply a thin coat of automotive paste wax to the characters and then place a piece of rubber insulation around the edges. The idea is to create a tight seal that will help prevent moisture from entering the tub.

There are several options for buying acrylic bathtubs and installing tub them in your home. Many homeowners use to go the do-it-yourself route and purchase an acrylic bathtub and shower combination kit. These kits typically include a bathtub, a pedestal, and a showerhead. They provide all the necessary materials for the homeowner to install tub shower combo their tub. However, these kits can sometimes include a more complicated installation process and may require the assistance of a professional plumber or another tradesman.

Remove the tub faucet and showerhead from the bathtub.

Many people wonder how to remove the tub faucet and showerhead from their bathtub without calling in a professional. The first thing that they need to do is find out just how many drains are in the bathtub. If it is a new bathtub, most likely, you only have one drain. Older bathtubs usually have two drains, each with a separate pipe for each. If your bathtub is a vintage bathtub, there may be more than one drain.

Find the center tap and turn it on; you will hear a clicking sound. You will see a white-colored mass of metal coming out of the top of the sink. There will be at least four drains on this pipe. Unscrew the end of the line from the tube and pull it out. On older models, there will be a retaining ring on the side. Take this out and discard it.

Use pliers to pull the retaining ring off the pipe. You will probably need to get a pair of wrenches, one for each side of the old drain and the new one. There will be at least three faucet holes, one on each side. You will have to take out the old faucet.

Initially, locate where the old tub connects to the drain. It will be labeled, and there should be a sign on it to indicate which side the drain attaches to. If you located this, unscrew it and then pull it straight up out of the gutter. Now, unplug the plumbing. You will want to have a mask to get any old water in your lungs or eyes. A plastic garbage bag works well.

Next, clean out all the parts of the old unit that you can. If pipes are sticking out of the drain, this will also make cleaning it more accessible. You should use a plunger or something to try to get any water out of it.

Once you have the old plumbing out, take some new equipment and tie it to the new pipe. This way, when the flapper is screwed onto the tube, it won’t come loose and cause you to lose the tub and drain. Put some plumber’s putty on the hook and then line it up with the hole you just drilled. Make sure it is securely in place, and then screw it on. There should be two or three spots where the plumber’s putty doesn’t seem to go, so be very careful.

When your tub and drain are all set, you can replace the tub faucet with the new one. As with the showerhead, you want to turn the hot and cold settings to the manufactures recommended settings. After you have everything connected, test the connection to make sure it all fits. It may be necessary to add a brass washer to prevent leaks.

When your bathtub and shower are all put together and running correctly, you will find that using them once a week will keep them in great shape for many years. Installing bathtub faucet and showerhead can be a relatively easy task. If you try something and it does not work as described, you can always call the person who sold you the piece.

When you try to remove your tub faucet and showerhead, you need to be extra careful. Make sure that the valves do not have any water resistance built-in. Also, be sure that when you turn on the water that it goes straight to the faucets. Before removing it, please turn on the water at the lowest setting to make sure it is draining correctly.

When you replace the tub faucet and shower head, be sure to install a seat and grab handles that you can use to close the tub and shower doors. It is also a good idea to establish a locking mechanism for the door to ensure that strangers cannot enter your home while you are away. It will help to secure you from theft. You will also want to look into replacing the tub seal and sponge. Most tubs will have an airtight seal, but some models may not.

Check the tub sealing mechanism as well. It may have become worn over time, or the seal may have even come off entirely. In both cases, you should replace it as soon as possible to prevent the tub from leaking. The tub faucet and showerhead will usually come with an installation kit, so be sure to follow the directions.

Tear out the old bathtub surround

So you want to tear out the old bathtub surround? Replacing bathtub surrounds is not as simple as just getting it painted or resigned. While you may think it’s possible to get rid of the old tub surround, it would be much better if you could instead take some time and replace it with a new one that will look nice in your bathroom. Here are some of the things you should consider when replacing the bathtub surrounds on your old tub.

Initially, locate the source of the leak. Get a tape measure and measuring the inside perimeter of the leak, or you can use a plumbing snake. You will know what kind of measurement you need to take after you get the measurements of the surrounding area. With the pipe wrench and a soldering iron, start to connect the two pipe clamps. Then you have to go back to the tub spout and remove the old bathtub surround. If it has the hardware, you need to remove the nuts that hold the pipe clamps in place.

Make sure to check your floor for cracks or crevices before you remove the bathtub surround. If you notice something on your floor that may concern you, make a mark on the paper with the dimensions of the hole or crack you found so that you’ll be able to accurately size the new drain hole when you buy the new tubs. You also have to ensure that you’ll have enough space to install the new drainpipe by figuring out how big the drain hole should be and how much plumbing is required to install the drain pipe. Also, measure the height of the wall studs that you’ve found and the diameter of the new drain hole.

Now, fill the existing sink area with a mixture of water and caulk. Use the plumbing pipe wrench to open the clamps of the old bathtub surround and then pull it out. Keep in mind that you need to turn off the water supply to your home first before you do this, or else there will be leaks when you do it.

Use the caulk to seal the cracks and holes on the surface of the old tub. But before caulk is even used, you have to make sure that the floor tiles of your bathroom are free from any debris so you can smooth out the caulk well with a rag. Apply the caulk to the whole area, including the floor tiles, the surround, and the tile around the shower valve. Let it dry for an hour.

After the drywall is thoroughly dry, you can now apply the tile backer board to the entire area. Ensure that you secure the backer board properly, as it may just fall off if not secured properly. Now install the new tub surround and the new shower valve, and the tile. Ensure that the drywall pieces are lined up correctly and that the drywall edges do not show.

When installing the new tub surround and the shower valve, you have to make sure that you do it right. First, start by lining up the perimeter walls and then marking the center of the new surroundings. Next, use a scale and a pencil to mark where the walls and the surround meet. You also need to take measurements of the tub spout to make sure that you can fit it through all the walls and spaces allotted. You also have to take measures of the floor space to see how much room you will have.

With these measurements, you can figure out how much caulk you will need. Use the low-side method for installing a new drain. Lay the caulk on the inside of the walls, and then, using the tips of your fingers, move it over the rim and up until you get to the topmost row of caulk where the drywall meets the walls. Now, use the level to level it off. Once the caulk is in place, you can install the new shower surround and the tile around it.

Remove old tub

Bathtubs, over time, will tend to appear aged, just like toilets and other fixtures inside a bath. It is simply because a lot of things happen in a bath. You might want to take the bathtub out of a bathhouse entirely and replace it with either a stand-up shower or a large jetted tub, or even install a smaller, electric-powered bathtub to add more comfort to your bath. However, before you can get a new bathtub into your bath, you must first remove the old bathtub. What follows after that is an easy process that should be painless for even a beginner!

Before removing the old bathtub, make sure the water supply pipe to the bath has not been leaking. If so, it is time to start removing the old bathtubs. To begin, unscrew all the nuts and bolts holding the old tub down from the floor. Two small holes allow you to slide it off at the bottom of the tub while unbolting it from the floor.

Once you have unscrewed the nuts and bolts holding it down, it is time to remove the old bathtub drain pipe. There are two small holes at the bottom of the bathtub. These are the access panel and the drain trap. Unscrew these fasteners from either side of the bathtubs to access the access panel and drain trap, respectively. On most models of bathtubs, this panel is right next to the drain trap. You can view the drain trap and access panel by turning the doorknob all the way open.

Next, remove the access panel by lifting it and prying open its access panel latch with a toothpick or other object. You can then remove the drain trap with a screwdriver or penknife. Once you have removed the drain trap and access panel, you will be left with the old tub drain pipe and its accompanying hardware.

Remove the dumpster from the wall to expose the plumbing beneath. The pipe was installed in a round hole in older bathtubs, so there will likely be a round hole where the pipe exits the drain. To help locate the pipe, it is helpful to look up under the bath. Look for a small drain plug. Once you have found this plug, insert a bolt under the outlet pipe and then twist it out.

Suppose you install a new bathtub in an existing bathtub; you will likely need to remove the existing surround. To do this, stand inside the tub and look towards the rear of the bath. There will be two S-shaped hooks that hang down from the bottom of the tub. These hooks are used to loosen the surrounding area that surrounds the drain pipes. Once the surround is relieved, it is easier to remove it and install the new one.

Once the surround is removed, the S-hooks can be installed behind the drain pipe and on either side of the S-shaped hook. The hooks are screwed into the surrounding panels to secure them in place. Once this is done, the new wall surface can be installed over the bathtub, and the surrounding areas repaired using caulk and caulking tape.

In most cases, removing and installing a bathtub will not be a big job. You can do this on your own. However, if you are not sure about how to remove and install a bathtub, it might be helpful to contact a professional plumber for advice. If you don’t want to pay for a professional to come and do the work for you, many videos are available on the internet to help you.

How to Replace a Bathtub?

How to replace a bathtub is a question that many people have. It is because one may feel incomplete without a nice bathtub. So before you spend thousands of dollars, take a look at these ideas.

The older bathtubs may be in fine shape. They need to have a few extra things taken care of to keep them in good condition for a long time. If you think this to be the case, you may want to consider supporting your bathtub and paying a low amount for a replacement.

The tub needs to be made out of cast iron. It will ensure that it is durable. You can pick from a different range of materials. If you want the tub to stand out, then go with glass or fiberglass. It is so your bathtub will blend in with the rest of your bathroom.

The other consideration is the depth of the tub. Your old tub may be deep enough, but you also need to consider your plumbing. Check around for old pipes and lines to see if you can recycle them. Do not throw them away. It may be worth salvaging them to fit into your new tub.

The tub should drain quickly. Drainage should be around half full at all times. Old tubs will drain slowly, which will make your bathroom feel uncomfortable and messy. It is not what you want.

Take a look at your plumbing. It will need to be in good shape. It could be that you are installing an electric shower. It requires special fittings that are not available on older tubs. A professional can usually recommend good choices.

How-to replace a bathtub on your own is not difficult if you follow these basic guidelines. If you decide to do it on your own, always take careful measurements before buying your tub. You want to fit it to code, and it needs to work with your existing plumbing. You also need to think about the installation costs, including your labor.

If you do not feel comfortable doing it yourself, hire a professional plumber. They will have more experience and know more about how to replace a bathtub on their own. If you decide to do it on your own, you will need the following tools:

A tape measure
A measuring tape
A pencil
A wrench set
A screwdriver
A water hose
A chemical cleaning product
The correct parts for your tub

If you do not have these items, search online for a local plumber. It may save you money to go to the local plumber rather than buying a replacement tub from a department store.

Now, you need to create a list of everything you will need to complete the job. Write down all of the materials you will need and the list of tools and their types. It is essential when learning how to replace a bathtub on your own. If you buy the wrong parts, your new tub could be dangerous.

Once you have your list of all the necessary materials, the next step in learning how to replace bathtubs on your own is to locate a licensed plumber. Visit your local Better Business Bureau to see if anyone has filed a complaint about the company you are considering. Ensure that the plumber has insurance and that the business is registered in your state. If your state only requires a company to be registered, this is a good indicator that the business ensures against plumbing emergencies.

How do you install bath surround?

Install the bathtub surround is an essential step if you want to get the best out of your bathroom. The bathroom surroundings are necessary since they provide privacy and also add to the beauty of a bathroom. This article will help you know how to install the bathtub surround and its installation. First of all, you have to measure the dimensions of the wall. Then you need to decide which material you want to use for the bathtub surround.

The most common material used for the bathtub surround is metal. It is available in colors and finishes. If you want something that completely blends with your bathroom, you can consider installing wood. However, metal is more appealing. To install the surround in the right way, you have to make sure that there is no space between the edge of the surround and the tub’s edges. This gap should not be more than 1 inch.

Now, remove the old surround. To do this, you should unscrew the bolts from the wall and then pull them up. When you are done, you should pull out the old surround. You have to ensure that there is enough space in front of the drainpipe to get blocked.

The third step in installing the bathtub surround is to install the metal framework in the front. Use a screwdriver. However, if you cannot handle the task, you should hire a professional. To anchor the metal frame, you should use some wood glue. Once you have glued the framework in place, you should wait for the glue to dry before tightening the nuts.

After installing the framework, the next task in the process is to install the drain. You have to place the handrails around the tub. Make sure that you attach them properly and securely to the framework. The next step is to identify the surround on the bathtub. The surround should follow the curvature of the surround.

After installing the surround, you have to check the position of the drain. You have to make sure that it is securely in its place. Once you have done all these, you should close the drain. The final step in learning how to install the bathtub surround is to replace the hardware. The hardware will help you maintain the plumbing in the bathroom.

Learning how to install the bathtub surround is quite simple. If you follow the directions, you will surely know how to install this tub surround in no time. In addition, you will be able to maintain your bathtub in good condition if you follow the proper procedure. You can use the suitable materials if you want to learn how to install the bathtub surround properly. There are options available in the market, so you do not have to worry about finding the best materials for the bathtub surround.

Installing the bathtub surround will not take a lot of time. You can learn how to install the bathtub surround in just 15 minutes. All you have to do is to follow the proper instructions. If you want to get more information, you can visit the websites of different plumbing companies. Each company will provide you with detailed information regarding how to install the bathtub surrounds.

Install the finished Plumbing

The first object to be considered in this article is How to Install the Finished Plumbing. Initially, know the characteristics of a finished plumbing system which has to be understood and then followed. The objects present in the system are the main pipe, the trap, the drain, and the nipple. The things may also include the seat, valve, handle, stem, and nipples as well. When we come to the Installation of the Finished Plumbing, we come across a series of activities that have to be performed. The series of activities comprises:

Plumbers are not aware of the series of activities required to be performed to install the finished plumbing. Many people do not realize the importance of these activities. Once you can install bathtub the finished plumbing, you will come across a series of events that should be completed within the given time. Installing the tub spout, spigot, tap, valve, and nipple is one task requiring regular attention. It will ensure that the trap will not leak at any point and prevent the faucet plate from rusting or getting twisted.

It is essential to understand that the new drain pipe should be placed at the end of the existing line. The end wall of the room’s end walls where the bathtub is installed will have to be extended. One of the main reasons the new bathtub has to be installed is the space factor. The bathroom area which is present in front of the tub is not enough. Therefore, space needs to be covered with tiles. If the surrounding area is exposed, then you should choose the seamless tile type. Another reason can be the shape of the bathroom floor.

The installation of the new bathtub is usually done inside the existing bathroom room. For the installation to be successful, you should ensure that the floor is pliable. After you have covered the floor with tiles, the next step is to install the plumbing pipes. These pipes are fastened onto the tiles on the edges of the floor. In case there are any gaps in the floor, experienced plumbers will repair them. They will replace the worn-out pipes with new ones.

When the plumber installs the plumbing work, they should also install access passageways to get the fixtures into the room where the bathtub is installed. It will help the users to gain access to the bathroom quickly. There are different types of access passageways available. You can install ordinary wallboards or install light switches with illuminated glass to make it easy for the users to see when they enter the room.

Install the new shower or bathtub with the latest plumbing and attached the light switches. Then, attach the old tub with the drain and the plumbing joints. Install the new tub according to the measurement given in your bathroom plan. If the measurements are not correct, there will be a gap between the two walls.

Use the correct plumb and level, as these will make sure that the drain position is correctly set up. Install the rough plumbing at the base of the bath unit to not create any problem during the installation. Connect the drain and the pipe fittings at the sides and the bottom of the rough plumbing. These should be connected to the pipes that are fixed at the floor level. Ensure that the pipe fittings are correctly seated, as this is important for the smooth flow of water from the drain to the bath unit.

Related Posts:

Install Tub Shower Combo