How To Replace Shower Faucet

Is it hard to replace shower faucet?

If you wonder is Replace shower faucet is difficult, then your answer is here. The faucet uses bunches of valves and handles to manage the temperature, pressure, and water flow to the shower and the bathtub. As far as issues are concerned, these factors are the cause of the replacement issue. Replacing a faucet is not a complicated process; it actually depends on the aspect you work with.

How much does a plumber charge to replace a shower faucet?

Around $147.27 to $350.88 bucks it will cost by average.

Do you have to replace valve when replacing shower faucet?

Yes, you can replace the valve while replacing the shower faucet.

How do you replace an old shower faucet?

  • Initially, Remove the Faucet Handles
  • Next, Remove the Spout
  • Finally, Remove Shower the Head and Shower Arm. Now replace the parts with new Parts.

How To Replace Shower Faucet

Replace shower faucet (How to?)

How to replace shower faucets? Replacing showerheads isn’t as difficult as it may seem at first glance. However, it’s essential to understand the process well to identify any problems right away, and the installation can continue smoothly. With a little bit of knowledge, you’ll find that installing a new shower head isn’t that hard, but it requires a little bit of work.

Before you start, ensure that you have all the necessary tools on hand so your project is not halted prematurely. These items and supplies are available at most hardware stores: changing shower faucets, clamps, drain nut wrench, replacement pipes, shower headcover, soap dispenser, soap dish, towel clips, wall anchors, screws and bolts, valve stems, wrench, plumber’s putty, molding tool, pipe fittings and joints, and molding clips. Now that you’ve gathered your tools, the next question is, how to replace the shower faucet? This step is self-explanatory; still, there are a few crucial steps that you should follow to prevent serious problems. If problems are encountered, read on for troubleshooting tips.

Initially, open up the showerhead and spray water into the fixtures. Turn on the water flow with a spray hose and watch the spray move down the shower pan. If the flow is too much, there will be excessive pressure in the line from the showerhead, which can cause clogs.

Next, you should close the showerhead. You can close it with two types of clamps: Swing arm clamps or T-shaped clamps. If either is the problem, you should turn the power off at the breaker box or the primary water source. Then, you should remove the clamps and the old showerhead.

The second step is to locate the problem faucets. Again, this step isn’t complicated, but you might find yourself using a screwdriver instead of a wrench if the problem is at a sink trap. Look for the “screw” part of the faucets. If you see a long pole coming out of the wall, the problem may be the seal.

Now, find out if the problems are solvable at home. For example, if you discover that the problem lies in the plumbing drain, you can replace it with a new one. However, if the problem is inside the fixture, the pipes are likely to be too damaged that re-keying them won’t help.

The third step on how to replace the shower faucet? You have to make sure that the pipes leading into the bathtub are clean. You can use a drain cleaning tool. It is imperative if you notice the pipes leak when you pour water on them.

See also  How Long Do Electric Car Batteries Last?

If everything goes well, your shower should work after a few days. If you discover that the problem is beyond repair or is already worse than before, don’t hesitate to hire a plumber. They will fix the problem correctly. Moreover, they will make sure that you enjoy the pleasant experience of using the new faucets. So, how to replace shower faucets?

Before purchasing any showerhead, you need to identify the type of faucets. For instance, there are antique claw-type and brass-style faucets. If you have antique claw-type faucets, you need to remove the old showerhead before replacing it with a new one. On the other hand, if you have bronze faucets, you need to turn off the water supply. Then, take out the old shower faucet, apart from the assembly and pieces attached to it.

To install new showerheads, you need to use pliers. These pliers are designed for working with plumbing. In addition, you need to lubricate them properly. Lubricate the joints between the shower faucet installation and showerheads, taking care not to damage the faucet body. If you’re using a threaded kind, you need to go further, unthreading the whole threaded part first before proceeding.

The next step on how to replace the shower faucet? You need to assemble the pieces back in their respective places. If there are numerous pieces, you can do the installation by yourself. However, if you have only one shower head, you need to make sure that you’ve purchased the correct pieces and correctly assemble them.

The last step on how to replace the shower faucet? Use water and soap to carefully wipe the new faucet parts to ensure they are perfectly aligned and secure. Wipe from the edges to the middle to prevent water leakages. After all, you don’t want the new shower head to leak just because you didn’t bother to follow the proper installation procedures.

3 Common issues of shower valve and pipes

Suppose your shower or bath is dripping; you can still fix the old faucet and temporarily replace the shower valve with cheap replacement parts.

If you want to have the latest feature like preset temperature and anti-scald protection, then you need to replace the new ones. You were connecting and changing shower fixtures and fix them with a new replacement. For this process, you need to know the essential plumbing work. Here, you will face few issues, and you will get a solution for those issues in this article.

Lack of Access Panel

For replacing a faucet, you need to work inside the wall. Lately, a few homes hold a removable panel in the next room back of the faucet. Suppose you don’t have an access panel, or you can’t find it; better lay a hole adjacent to the shower surround. Here is the tip, better fix a paintable plastic panel, back of the faucet, because you can find it in a different size in plumbing supplies. You can purchase a 14 x 14-inch panel.

See also  Best Drywall Anchors Reviews 2022

Don’t attempt to place the access hole with measurements. Alternatively, exclude faucet handles or tub spout and put a marker hole in the wall. If the wall is less dense, you can use a drill or screwdriver to punch a hole. Before proceeding with the access panel, make a small hole with the drill bit to identify the spot.

Now, utilize the access panel to mark the fill size hole. To avoid the damage, fix it after the faucet is replaced.

Steel Pipe (Galvanised)

Steel pipes are connected using a threaded screw head to join; it is not like plastic or copper. So, it is not a simple process to disconnect the cold and hot pipes alone. It will exclude the threaded ends, and you will not have a reliable option to link your new pipe.

To protect those threaded heads, extract the union fittings connected to the supply pipe to the faucet. You can let the spout nipple joined to the faucet and drag it with the shower valve installation. Suppose your faucet is connected with the showerhead, cast the shower riser pipe since this pipe will not hold a constant pressure so that you have the option to reconnect it with a pipe coupler.

Now, Link your new faucet. To link the shower riser, which is cut off previously, use a compression coupler specially designed for galvanized steel pipe. Apply Teflon pipe sealant for an excellent and better seal and installation purpose. You can also use it for coupler thread and rubber seals. Here is the climax part: turn ON the shower and check for leakages; if you are failed in the project, you should tight the coupler’s nuts and screws if there is leakage.

Replace shower faucet

Troubleshooting during a shower faucet replacement should be the first thing that comes to your mind. Replacing the shower faucet can be a tricky task if the old one has been damaged or broken. Replacing the old shower faucet with a new one requires you to know the troubleshooting techniques not to ruin the installation.

Test the functionality of the new valve on the mounting surface to see if you have the correct one in place. Sometimes, troubleshooting during a shower faucet replacement may require you to turn the valve off, turn on the hot water supply valve and test the functioning of the valve. Once you are sure that the valve works correctly, turn it off and remove the old one from the pipe.

First, search the entire house for missing screws or other signs of a leak. There could be a hidden leak somewhere in the house, especially in the walls near the plumbing pipes. Look carefully at the bathtub and the shower faucet replacement valves. If you find any signs of a leak, you have to replace them with new ones before starting the job.

Second, search for the missing screws on both valves. These often accumulate dust and become challenging to find when there are damaged parts on them. You have to remove them carefully to replace them with new ones. Attach the adjustment nut tightly to the wall studs. Turn the adjustment wrench clockwise until the valve comes out of its socket.

See also  Who Makes Continental Tires? Complete Guide

Third, use your adjustable wrench to loosen the nut on the end of the pipe that connects the supply line and the valve. You have to ensure that the valve is entirely open because you don’t want water coming out while you’re changing shower faucet replacement parts. Take note of how tightly the nut is snugged down. You can use your screwdriver to turn the adjustment screw clockwise to loosen it more.

Fourth, place the new shower faucet replacement parts onto the existing screw terminal and screw them firmly into place. Use the pliers to compress the screw terminal to hold it firmly in place. With your adjustable wrench, turn the new screw-in clockwise. It will loosen the old replacing shower valve from its holding position on the pipe wall. Remove the old showerhead and pieces of the old fence.

Fifth, reconnect the valve and flush out the old plumbing connection. You can use the existing plumbing pipes as long as they are securely in place to ensure that the shower faucet replacement fixture is secure. However, if you have badly damaged or broken connections, you have to replace the entire plumbing structure.

Shower faucets are not hard to replace. You can easily do it by yourself. There’s no need for you to call on a plumber just because you’re installing a new showerhead. You need to know about plumbing installation to follow instructions carefully and carefully install the fixtures to ensure their solidity and durability. YSave a few bucks by doing the shower faucet replacement on your own.

The plumbing work for shower faucet replacement does not only include the replacement of the existing shower valve. It also provides for the installation of new fixtures. You can find different types and styles of shower valves in the market.

Some change shower faucets are sold as one-piece units. These are perfect for people who want to save some money and time for plumbing installation. You’ll have to replace a single valve for one tub and then the other for the other tubs. However, if you’re a busy individual who doesn’t have enough time to complete the plumbing installation yourself, you may choose to purchase two-piece shower faucets. With two-piece units, you have the option of replacing a single tub with two separate ones.

To reduce the plumbing expenses and the total plumbing expenditure, you should take care of the problems as early as possible. Find out if you have to replace the corroded washers with new ones. Or, maybe the shower faucet replacement needs only a tiny amount of rust to be completed.

Tools requirements

  • Corded drill
  • Adjustable wrench
  • Pipe wrench
  • Drywall saw
  • Jigsaw
  • Safety glasses
  • Pliers
  • 4-in-1 screwdriver
  • Soldering torch
  • Tube cutter
  • Reciprocating saw
  • Screwdriver
  • Tape measure

Material requirements

  • Pipe joint tape
  • New valve
  • Shutoff valves
  • Plastic access panel
  • Copper fittings
  • Renovation cover plate

 

 

 

Leave a Comment