How To Remove Scratches From Stainless Steel

Stainless steel is famous because of its sleek appearance and long-term durability. It’s an excellent material for cookware, kitchen appliances, sinks, fixtures, and other home and office products. Unfortunately, stainless steel may be scratched in a microwave, dishwasher, or refrigerator.

However, you don’t have to deal with scuffed steel indefinitely! To remove scratches from stainless steel appliances, follow these basic steps. Bear in mind that these methods can only be used on stainless steel that hasn’t had a protective clear coat or synthetic surface applied to it.

How To Remove Scratches From Stainless Steel

Fine scratches

Comet, Revere Stainless Steel, and Copper Cleaner can gently buff stainless steel to prevent fine scratches. If none of these are available, appliance manufacturers frequently produce their cleaners readily available at home improvement stores. A stainless-steel polish may also be used to mask minor scratches.

Deep scratches

Sandpaper is your match for deeper scratches and acts as a stainless steel scratch remover. Deeper scratches can be removed with a piece of wet fine-grit sandpaper. Still hold it warm, and then rub it in with a rubbing paste.

Start with the scratch and work your way up. Determine the grain’s path and begin sanding in a single direction, following the brushed pattern. Sanding back and forth is not recommended, as is sanding against the grain. If you need to remove deeper scratches, start with a coarser grit paper, then a finer grit, and finally, rubbing compound.

Only simple (uncoated) stainless steel panels are suitable for sanding: On simulated stainless steel or stainless panels with a fingerprint-resistant transparent coat, don’t do it.

Clean and polish

You can clean and polish your stainless-steel appliance after removing scratches and unwanted marks. Wipe down the freshly sanded surface with a clean microfiber rag. Sanding and metal particles, as well as any remaining polishing compound or water, will be removed. It’s also necessary to rub and buff in the direction of the grain while washing.

See also  How To Replace Shower Faucet

Spray the metal with many vinegar sprays, then rub it off with a clean microfiber cloth for best results. The vinegar will eliminate any traces of other compounds and cleaners from the soil.

Start polishing once the stainless steel is clean and dry. Using a clean microfiber cloth, apply a few drops of oil. Mineral oil, vegetable oil, or even olive oil may be used. To polish the metal, rub the cloth against it in the direction of the grain. As required, add more oil. Rubbing should be continued until the whole surface is polished.

Following these measures will keep your stainless-steel surface scratch-free while also bringing out the brand-new shine you fell in love within the first place.

Can you get scratches out of stainless steel?

Light scratches are the simplest to remove, and they can usually be buffed off with a non-abrasive cleanser: if using a powder, combine with a bit of water to make a paste. Rep the procedure until you’re pleased with the performance, then finish with a thin coat of stainless steel polish or olive oil.

Does toothpaste remove scratches out of stainless steel?

Apply the toothpaste to the toothbrush and gently work the solution over the scratched stainless steel in the grain’s direction. Wipe away the toothpaste with a clean, damp cloth and check for a scratch. Rep the procedure until you’re pleased with the performance, then finish with a thin coat of stainless steel polish or olive oil.

Scratches may be removed with toothpaste. With a soft cloth and a dab of toothpaste, you can easily remove scratches without much effort. When toothpaste is gently applied onto a slick, smooth surface, it adheres to the surface and sands away scratches.

See also  How to Clean Your EGR Valve?

Can WD 40 remove scratches out of stainless steel?

Spray WD-40 directly on the appliance or onto a cloth, then wipe away. Although WD-40 will clean your stainless steel appliance, it is a petroleum-based product that should be used with caution on or near any surface where food will be handled.

How do you get deep scratches out of stainless steel?

Using a stainless steel scratch removal kit including Scratch-B-Gone or Siege Stainless Steel Sink and Cookware Scratch Remover for larger imperfections that don’t react to the compound. A polishing agent and a set of abrasive pads are normally included in scratch remover kits. For stainless steel scratch repair, you’ll use grits ranging from coarse to fine.

Be sure to follow the manufacturer’s instructions for your particular package.

  1. Thoroughly read the manufacturer’s directions. Determine the grain orientation in your stainless steel.
  2. Begin by rubbing the scratch with the grain in one direction only, using the appropriate grit pad for the particular scratch you want to remove. Going back and forth with an abrasive could result in unsightly circular marks. Use just as much pressure as is necessary to fix scratches in the stainless steel; don’t go any deeper than is needed.
  3. If the manufacturer recommends it, switch to a smoother grit pad and continue buffing, adding water or any compounds provided in the kit as required.
  4. To complete the process, wipe the steel with a microfiber cloth and buff it to a lustrous sheen.

Stop using abrasive chemicals or steel wool for routine cleaning and repairs to keep the metal surfaces looking fresh. When washing large pots or cast iron, use a rubber dish mat to protect your stainless steel sink. Just be sure to take the mat off when you’re done washing up so that water doesn’t get stuck underneath and cause discoloration.

See also  Symptoms of a Bad Coolant Temp Sensor

How to remove fine scratches in stainless steel?

Use a non-abrasive cleaner like Bar Keeper’s Friend or Revere Stainless Steel and Copper Cleaner to remove the tarnish. (If you’re in a hurry, whitening toothpaste will suffice.)

  1. If you’re using a powdered stainless steel scratch remover, apply just enough water to make a paste the consistency of toothpaste, a few drops at a time. Proceed to the next step if your compound of choice is cream-based.
  2. Apply a small amount of scratch remover compound to a microfiber cloth and gently smooth it over the scratch in the metal’s grain direction. Continue until the scratch is no longer visible.
  3. To remove any compound residue, clean the surface with a new, barely damp microfiber cloth. Using a new microfiber fabric, dry thoroughly. If necessary, repeat Steps 2 and 3 to remove any scratches from stainless steel surfaces.





Leave a Comment