How to Remove Rear Axle Bearing Without Puller

If you’re planning on doing some work on your car’s rear axle, you might be wondering how to remove the rear axle bearing without a puller. Here’s a quick guide on how to do it.

First, you’ll need to remove the rear axle shaft. To do this, you’ll need to remove the brake drums, wheels, and axle nuts. Once the axle shaft is removed, you can access the rear axle bearing.

To remove the bearing, you’ll need to press it out of the housing. You can do this with a bearing press or a hydraulic press. Once the bearing is out, you can clean up the housing and install a new bearing.

Steps to take if you want to know how to remove bearing from the shaft without a puller

If you need to remove a rear axle bearing without a puller, there are a few steps you can take. First, you’ll need to remove the axle shaft from the vehicle. Next, you’ll need to remove the retaining ring that holds the bearing in place. Finally, you’ll need to use a hammer and punch to remove the bearing from the shaft.

How to remove Axle bearings on Drum brake vehicles

Removing an axle bearing without a puller can be a difficult task. Many people choose to use a puller because it makes the process much easier and quicker. However, if you do not have a puller, there are still ways that you can remove the axle bearing.

One way to remove an axle bearing without a puller is to use a chisel and a hammer. First, you will need to find the spot where the bearing is seated. Once you have found this spot, you will need to place the chisel on the bearing and hit the chisel with the hammer. This will loosen the bearing so that you can remove it by hand.

Another way to remove an axle bearing without a puller is to use a pry bar. First, you will need to find the spot where the bearing is seated. Once you have found this spot, you will need to place the pry bar under the bearing and pry it up. This will loosen the bearing so that you can remove it by hand.

If you are having difficulty removing the axle bearing without a puller, you may need to take your vehicle to a mechanic. Many mechanics have the tools and experience necessary to remove the axle bearing without damaging the vehicle.

Select the right surface

When removing a rear axle bearing without a puller, it is important to select a flat surface to avoid damaging the bearing. A workbench or table is ideal. Place a block of wood under the bearing to be removed, and use a hammer to tap the bearing out of the axle. Be sure to tap evenly around the circumference of the bearing to avoid damaging it.

Apply the vehicle’s parking brake

The parking brake is a critical safety feature on any vehicle. It is important to make sure that it is in good working order and is applied correctly.

To apply the parking brake on most vehicles, first locate the pedal or lever. In some cars, the parking brake is a pedal, while in others it may be a lever. Once you have located the parking brake, apply firm pressure to engage it. You should hear or feel a click when the brake is engaged.

It is important to remember to disengage the parking brake before driving. Most cars have a warning light that will come on if the parking brake is engaged. Once you have disengaged the parking brake, make sure to give the car a little extra gas when pulling away from a stop to make up for the resistance from the brakes.

See also  How to Make a DIY Wood Pallet Planter, Our Easy Tutorial Gives You All the Answers!

Place jack stands under your vehicle

If your vehicle has rear axle bearings, you will need to remove them at some point to replace them. This can be done without a puller, but it is much more difficult. First, you will need to place jack stands under your vehicle. Next, you will need to remove the axle shaft from the differential. Once the axle shaft is removed, you can remove the bearing.

Remove the coverings and trays that are in the way

Assuming you have a rear axle bearing puller:

1. Remove the coverings and trays that are in the way.
2. Insert the puller into the center of the bearing.
3. Turn the screw on the puller until the bearing pops out.

Remove the tires

Assuming you have a rear-wheel drive car, the first thing you’ll need to do is remove the tires. To do this, you’ll need to loosen the lug nuts with a wrench. Once the lug nuts are loose, you can use a jack to lift the car up and remove the tires.

Next, you’ll need to remove the brake caliper. The brake caliper is what holds the brake pads in place, and is located on the back of the wheel. To remove it, you’ll need to first remove the bolts that hold it in place. Once the bolts are removed, you can pull the caliper off of the wheel.

After the brake caliper is removed, you’ll be able to see the axle shaft. The axle shaft is what the wheel is attached to, and is what the bearings are located on. To remove the axle shaft, you’ll need to first remove the bolts that hold it in place. Once the bolts are removed, you can pull the axle shaft out of the car.

Finally, you’ll be able to remove the bearings. The bearings are located on the axle shaft, and are what the wheels rotate on. To remove the bearings, you’ll need to first remove the bolts that hold them in place. Once the bolts are removed, you can pull the bearings off of the axle shaft.

Unbolt the caliper and remove the Brake pads from it

Begin by unbolting the caliper and removing the brake pads from it. Next, remove the axle nut and washer. With the axle nut and washer removed, the axle shaft should be free to slide out of the axle housing.

Release your vehicle’s parking brake

If your vehicle has a parking brake, release it before starting this process. If your vehicle does not have a parking brake, make sure to block the wheels to prevent the vehicle from rolling while you work.

Next, you will need to support the vehicle so that the rear wheels are off the ground. You can do this by placing jack stands under the vehicle at the appropriate points. Consult your vehicle’s owner’s manual to find out where to place the jack stands.

Once the vehicle is supported and the rear wheels are off the ground, you can begin to remove the rear axle bearing. Start by removing the nut that holds the bearing in place. This nut is usually located at the end of the axle shaft.

See also  Who Makes Tracker ATV?

Once the nut is removed, the bearing can be pulled off the axle shaft. You may need to use a pry bar or a hammer to loosen the bearing from the shaft. Be careful not to damage the shaft as you remove the bearing.

With the bearing removed, you can now proceed to remove the axle shaft from the vehicle. This process will vary depending on the type of vehicle you have. Consult your vehicle’s owner’s manual for specific instructions.

Once the axle shaft is removed, you can proceed to remove the rear axle housing. This process will also vary depending on the type of vehicle you have. Consult your vehicle’s owner’s manual for specific instructions.

With the rear axle housing removed, you will have full access to the rear axle bearings. You can now proceed to remove the bearings from the axle housing.

To remove the bearings, start by unbolting the bearing caps from the axle housing. Once the bearing caps are removed, the bearings can be pulled out of the housing.

With the rear axle bearings removed, you can now proceed to install the new bearings. Start by cleaning the axle housing and bearings with a degreaser. This will remove any dirt or debris that could cause problems during installation.

Next, place the new bearings into the axle housing and bolt the bearing caps back in place. Make sure the bearings are properly seated in the housing before tightening the bearing caps.

Once the new bearings are installed, you can now reinstall the axle shaft and the rear axle housing. This process will vary depending on the type of vehicle you have. Consult your vehicle’s owner’s manual for specific instructions.

With the axle shaft and rear axle housing reinstalled, you can now proceed to install the new rear axle bearing. Start by sliding the new bearing onto the end of the axle shaft.

Next, place the nut that holds the bearing in place and tighten it to the appropriate torque. Consult your vehicle’s owner’s manual or a service manual to find the correct torque for the nut.

Once the nut is tightened, you can now proceed to lower the vehicle off of the jack stands. Make sure the parking brake is engaged and the wheels are blocked before doing this.

With the vehicle back on the ground, you can now test drive it to make sure the rear axle bearing is functioning properly. If everything seems to be working correctly, you can consider the job complete.

Remove the vehicle’s disk rotor

Assuming you have a disc brake set up, the first thing you’ll want to do is remove the disc rotor. To do this, you’ll need to remove the retaining screws or bolts that hold it in place. Once the rotor is removed, you’ll be able to access the rear axle bearing.

Remove the wheel/Brake drum

To remove the rear axle bearing without a puller, first remove the wheel or brake drum. Next, remove the cotter pin and nut from the end of the axle. With the nut and cotter pin removed, the axle should be able to be pulled out of the housing. Finally, remove the old bearing from the housing and press the new bearing into place.

See also  Top 10+ Best Grease For Ball Joints In 2022

Disconnect your brake shoes

To remove your rear axle bearings without a puller, first disconnect your brake shoes. You can do this by removing the retaining clips that hold them in place. Once the clips are removed, the shoes will come off easily. Next, remove the axle nuts. These are typically located on the hub, and can be removed with a wrench. Once the nuts are removed, the axle will slide out easily. Finally, remove the bearings from the axle. These can be removed with a punch or a chisel.

Removing the bearing from the axle shaft

There are a few ways to remove a rear axle bearing without using a puller. One way is to use a chisel and a hammer. Place the chisel on the inner race of the bearing and tap the chisel with the hammer until the bearing pops off the axle. Another way is to use a slide hammer. Attach the slide hammer to the bearing and pull the bearing off the axle. Finally, you can use an air hammer. Place the tip of the air hammer on the inner race of the bearing and press the trigger until the bearing pops off the axle.

Installing the new axle bearing

1.Using a pry bar, remove the old axle bearing from the housing.

2.Clean the housing with a degreaser and a brush.

3. Inspect the housing for any damage.

4.Using a press, install the new axle bearing into the housing.

5.Install the retaining clip or c-clip.

6.Torque the axle nut to the specified amount.

Frequently Asked Questions (FAQs)

1. How do I remove a rear axle bearing without a puller?

There are a few ways that you can remove a rear axle bearing without using a puller. One way is to use a large screwdriver to pry the bearing out of the housing. Another way is to use a hammer and punch to drive the bearing out of the housing.

2. What are the benefits of removing a rear axle bearing?

There are several benefits to removing a rear axle bearing. One benefit is that it allows you to inspect the bearing for any damage. Another benefit is that it allows you to clean the bearing and the housing.

3. What are the risks of removing a rear axle bearing?

There are a few risks associated with removing a rear axle bearing. One risk is that you could damage the bearing. Another risk is that you could damage the housing.

How to Remove Rear Axle Bearing Without Puller

Must Read

-To remove rear axle bearing without puller, first you need to remove the axle nut. Use a socket wrench to loosen the nut.

-Then, use a hammer to tap on the end of the axle. This will help to loosen the bearing.

-Next, use a pry bar to pry the bearing out of the housing.

-Finally, clean the area where the bearing was located.

Conclusion

Thanks for reading! I hope this article was helpful in learning how to remove a rear axle bearing without a puller. If you have any questions or comments, please leave them below. As always, happy wrenching!

Leave a Comment