How To HotWire A Car? Very Easy Methods

Hotwiring a car is not as difficult as it may seem. There are a few very easy methods that can be used to hotwire a car. This blog post will show you how to hotwire a car using two very easy methods.

How to hotwire a car step by step guide

1. Locate the car’s fuse box. This is usually located under the dashboard on the driver’s side.

2. Find the fuse for the car’s ignition system. This is typically a large fuse labeled “IGN.”

3. Use a pair of needle-nose pliers to remove the fuse from the fuse box.

4. Find a bare wire in the car’s engine compartment. This can be found by following the wiring from the fuse box to the engine.

5. Strip the insulation off of the end of the wire using a wire stripper.

6. Touch the end of the bare wire to the metal contact on the back of the ignition fuse.

7. Turn the key in the ignition to the “On” position. The car should start.

The steering wheel method 

Assuming that you have a basic understanding of how a car’s ignition system works, hotwiring a car is not that difficult. The most common method of hotwiring a car is to bypass the ignition switch by connecting the two wires that go to the starter solenoid directly. This can be done by using a screwdriver to pry up the plastic cover on the steering column and then using a pair of pliers to twist the wires together.

Another method of hotwiring a car is to bypass the ignition switch by disconnecting the wire that goes from the ignition switch to the starter solenoid and then connecting the two wires that go to the starter solenoid directly. This can be done by using a screwdriver to remove the plastic cover on the steering column and then using a pair of pliers to disconnect the wire from the ignition switch.

See also  How to Remove Pilot Bearing [Symptoms and How to Fix]

Once the wires are connected, the car should start. If it doesn’t, you may need to check the fuse box to make sure that the fuse for the starter solenoid is not blown.

The jumper cable trick (the hood)

Assuming you have a friend to help you with this, and that your car has the standard North American under-the-hood layout, here’s how to do it:

1. Open up the hood and locate the battery.

2. Have your friend attach one end of the jumper cable to the positive terminal of the battery.

3. Have them take the other end of the jumper cable and attach it to the positive terminal of the starter.

4. Have them take the other end of the jumper cable and attach it to the negative terminal of the battery.

5. Take the other end of the jumper cable and attach it to a metal ground on the car.

6. Have your friend turn the key to the “on” position.

7. Once the key is in the “on” position, have them turn the key to the “start” position.

The car should start right up!

FAQs

1. Can I hotwire a car if I don’t have the keys?

Yes, you can hotwire a car if you don’t have the keys. However, it’s important to note that this is generally not considered to be the best or safest method. If possible, it’s always best to use the keys to start the car.

2. Is it easy to hotwire a car?

It can be easy to hotwire a car, depending on the make and model. Some cars are easier to hotwire than others. However, it’s important to remember that hotwiring a car is generally not considered to be the best or safest method.

See also  DIY Bathroom Vanity in 40 Inspiring Ideas

3. What are the risks of hotwiring a car?

There are a few risks associated with hotwiring a car. First, you could damage the car’s ignition system. Second, you could be electrocuted if you’re not careful. Third, hotwiring a car is generally considered to be a crime, so you could be arrested if you’re caught.

How To HotWire A Car? Very Easy Methods

Must Read

1. Find the right tools. You’ll need a screwdriver, a wire cutter/stripper, and a pair of pliers.

2. Locate the ignition switch. It’s usually located near the steering column.

3. Use the screwdriver to remove the screws that hold the ignition switch in place.

4. Cut the wires that lead to the ignition switch.

5. Strip the ends of the wires.

6. Touch the stripped ends of the wires together.

7. Turn the key in the ignition.

8. Start the car.

Conclusion

Thanks for reading our blog post on how to hotwire a car. We hope you found the information and instructions helpful and that you were able to successfully hotwire a car using one of the methods we outlined. If you have any questions or comments, please feel free to leave them below.

Leave a Comment